DLG90 type extruder-manufacture,factory,supplier from China

For extruder equipment, the model specifications of extruder equipment are classified according to the diameter of the screw. For the sake of explanation, plastic is used as an example below, but the same is true for food extruders.That is to say, the screw diameter of the extruder equipment is the model specification of the extruder equipment. For example, the screw diameter of the 90-type extruder equipment is 90mm.

A particular chemical or biochemical reactionExtruder is a new type of biochemical reactor, food in the process of being extruded, will have a series of biochemical reactions.

Twin screw extruder is developed on the basis of single screw extruder. Two screws are placed side by side in the barrel of the twin screw extruder. According to the meshing degree of the two screws can be divided into mutual meshing type and non-meshing type. According to the rotation direction of the two screw shafts, it can be divided into reverse rotation type and co-rotation type.(1) meshing twin screw: Because the meshing gap of the meshing screw is very small, the material has the ability of forced conveying, not easy to produce backflow, leakage phenomenon.

Feed extruder is a single screw extruder. Mainly used for food puffing, livestock feed or used for puffing single raw materials, but also as a plant oil and drinking wine production of raw materials in the pre-place. Twin-screw extruding extruder, mainly used for the production and processing of high-grade aquatic products, pet materials, especially the processing of viscous materials.What are its characteristics?1.

There is only one screw in the barrel of the single screw extruder, it is by the friction of the screw and the barrel of the material to transport materials and form a certain pressure. In general, the friction coefficient between the material and the barrel is greater than that between the material and the screw. Otherwise, the material will be wrapped in the screw together to rotate and not play the role of forward propulsion.Screw is divided into three sections: feeding (feeding) conveying section, compression melting section, metering homogenization section.

Directly puffed food is generally required to be dried after extrusion processing. The moisture content of the dough in the extruder is 15%~20%. The product is then dried to reduce the moisture content to 2% to 3% to create the environment needed for a crunchy texture and stable shelf life. Due to the low density of the product, the drying time is usually very short, so it should be carried out in a warm warehouse.Coatings to produce direct-expanded products Extruded and dried products are finally sprayed with oils and seasonings.

Working Principle of Twin Screw ExtrusionAfter a certain amount of pulverization, the material with a certain water content is fed into the extruder cavity, so that the material will undergo mixing, shearing, A series of complex continuous processes such as melting, curing and sterilization. Because there is a certain air pressure difference inside and outside the barrel, the moment the material is extruded, the external pressure it is subjected to is reduced to normal pressure, so that the material is instantly puffed.

　　Before you get a food extruder, make sure you do your homework on the machine you’re buying so you can get the most out of it. Consider these things before you buy an extrusion machine.Type Of Extruder:　　Piston extruders, roller-type extruders, and screw extruders are the 3 kinds of extruders commonly used to make packed food products, with the latter being the most common.　　For food processing, you should determine if you require a single-screw extruder or a double-screw extruder.

Series double screw extruder introduction:1, mainly by the feeding system, extrusion system, rotary cutting system, heating system, lubrication system, control system.2, extruder feeding system, main drive system, rotary cutting system all adopt frequency control, strong power, smooth operation, power saving.3, automatic lubrication, forced cooling, to ensure the safe operation of the extruder and prolong the life.4, screw alloy material, through special processing, high strength, wear resistance, increase the service life.5, according to different products, with different structure and length

When operating a twin-screw extruder, it should be maintained on time. The maintenance process is carried out after the twin-screw extruder runs continuously for 2500-5000h and shuts down. The screw is extracted to inspect, measure and identify the wear condition of the most critical components, replace the components that have reached the specified wear limit as soon as possible, and repair the damaged components . The maintenance standard of the reducer of the twin-screw extruder is the same as that of the ordinary standard reducer.